45 Online retailers selling the NTK
Like it’s bigger brother the K2, the RØDE NTK is a premium valve condenser microphone designed to provide incredible detail and warmth in the studio. Its cardioid polar pattern is perfect for most single instrument recording scenarios.
The electronic circuitry complementing this very sensitive transducer includes a hand-selected twin-triode 6922 valve and audiophile grade components. The result is an ultra-wide dynamic range, low noise, and stunning tube warmth. The NTK's rich valve sound is ideal for vocals, acoustic instruments, drum overheads, guitar amps and pianos.
The RØDE NTK microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
|Acoustic Principle||Pressure Gradient|
|Active Electronics||Valve/tube impedance converter with bipolar output buffer|
|Frequency Range||20Hz - 20kHz|
|Maximum Output Level||29.0mV (@ 1kHz, 1% THD into 1KΩ load)|
|Sensitivity||-38.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz|
|Equivalent Noise Level (A-weighted)||12dBA|
|Dimensions||208.00mmH x 55.00mmW x 55.00mmD|
|Warranty||1 year with free extension to 10 years following registration here|
The NTK will put you on equal footing, or better, with many new and vintage microphones that cost several times as much.
I love the NTK. My guess is that it will still sound great 40 years from now.
The proof is in the listening, for sure. They sound fantastic. Startlingly fantastic, perhaps as good as any mic in the world. Certainly as good as any mic I have ever used, and yes that includes the obvious.
When we plug the NTKs in and powered up the power supply, all of a sudden we realized what we were missing. The mics are smooth and brilliant.
The Rode NTK lives up to all my expectations in sounding both warm and flattering, yet open and detailed. Every subtle vocal articulation is captured... I like it very much!
Both the NT1000 and NTK are examples of excellent efforts from RØDE. Based on specs and clearly audible quality of sound in the studio, these mics cannot be ignored.
While most would understandably be interested in the NTK as a vocal mic, and it is a good one, it makes a great all-around mic for many purposes. Recently I used one on a bass guitar cabinet. After trying several other high quality dynamic and condenser mics first the NTK was the one that brought the proper balance of articulation, low end, and warmth to the track. Great all around mic.
To my instant surprise, the NTK immediately delivered warm, clear, and full-bodied sound! Since then I've used the NTK in hundreds of various recording situations, and with a multitude of different instruments including vocals, acoustic guitars, classical guitars, upright bass, percussion, and more. I love to create sounds using two microphones of different make and model in a stereo field, but almost always the NTK is included. It sounds great paired with a KSM44, or 414. I've even used two NTKs as drum overheads, and they sounded fantastic!
There is no better condenser microphone at this price range, and purchasing the NTK has been one of the wisest "mistakes" of my recording career.
I was amazed by the clarity and warmth of the NTK. Let's be honest, most well known microphone brands trade on their name.I have auditioned most brands out there, and can say with the greatest of confidence that you dont have to spend $7000 to get a good sound.
This mic has replaced my Shure condenser for almost all my voice work. I do a lot of spoken word production which requires an intelligible mic with a distinct presence. The NTK has both. My production now stacks up better on-air against the bigger studios. I also record rock and folk vocals and again, the RØDE does very well in these applications.
What a great mike - not just for the money. This mic is a clear example of why you do not need to mortgage your house to get absolutely pro sound - RØDE has done the recording musician a huge favor. If you want warm and clear vocals and acoustic guitar, this is perfect- buy one and set the mike up and play and sing. You won't be sorry.
It is recommended to have this done by your nearest authorized RØDE service centre, however if you wish to do this yourself you must be very careful not to injure yourself. Ensure the microphone is not powered, and that you are grounded before touching any circuitry.
No, whilst these power supplies do not require phantom power, they are built to cope with being fed phantom power and this will not damage the equipment. It is however advised that where possible, to turn off phantom power when not in use.
The cable between the K2 microphone and the K2 power supply uses a standard 7 pin XLR connection. Whilst not widely available, any good professional audio shop should be able to get hold of the parts to make one for you. The cable is pin to pin.
Please be aware that you should only use good quality cable and connectors for connection between the PSU and the mic. Replacement cables are available from RØDE through our chain of distributors, RØDE can only supply the cable in a standard 10m length.
The tubes we use in our microphones have been selected to give our customers the best performance possible with our designs. Low noise, sound quality and of course long life are taken into consideration with every design and subsequent tube selection.
The tubes are purchased in bulk from various manufacturers which we then subject every tube to a series of tests that start with a 'burn in' period that will result in those tubes that do not meet our high tolerances being rejected. We test for noise, microphonics and output.
These tubes have a very long working life and in many cases we have found RØDE tube microphones that have been used for over 10 years that still meet full specifications.
RØDE Tube Mics,Tube (graded and selected for low noise)
That depends on the tube. It could be a low-quality old tube!
Do some research on the tube sites and you will start to get an idea of what is good and what is just 'smoke and mirrors'. There is quite a lot of mythology surrounding tubes with wild claims being made. The reality is that tube technology was at its peak in the 50&60's and so it stands to reason that the manufacturers of that time did have some mature technology, and so produced high-quality, high-tolerance devices.
When transistors started to take over, the demand for premium and high specification tubes started to decline to the point where none of the high end producers in the US, Germany or UK were viable and so their production ceased. Tubes continued to be made in Russia and other 'soviet block' countries, and of course China - in many instances these were for military applications. These factories have been at the forefront of the current tube supply, but it must be remembered that other than the audio industry, there is no need for tubes today and that is why the brands such as Telefunken, GE, Sylvania, Mullard etc are not in the game anymore.
How will you know what to buy? There are many web sites and vendors for NOS tubes and they supply lots of information. If you have the time, start reading and you will begin to see a pattern where certain old brands and styles keep being mentioned. That is a good guide.
The prices are rising because of rarity, but modern production for certain tubes such as the ones we currently use in our microphones is certainly equal to anything from the past. It comes down to knowing how to select and test, and of course grading them accordingly. It is fun to experiment, so go ahead, but please ensure you don't use tubes not designed for the circuit, or the results will not only disappoint, but you could also damage your microphone.
This is a complex question, which depends on many factors. The tubes we use are of very high quality and have been selected to be the optimum choice for our designs. There are many NOS (new old stock) tubes on the market that in some cases can change the tonal, noise and distortion characteristics of your microphone.
While you may be happy with the result, you may also be disappointed and find the tube that came with the microphone sounds better. To find out, you will need to experiment and that can be expensive but of course the choice is yours if you wish to experiment.
We choose our tube type carefully to allow us to have enough stock to manufacture in the quantites required to satisfy our customers whilst keeping the mic characteristics constant and to ensure support for the product for many years to come.
All tubes are microphonic to a certain degree. That means if you tap them when in circuit you will hear that sound in your signal. Some are much worse than others, and can cause problems when they are modulated by vibration, or in extreme cases even by the sound you are recording!
How do you get a low-microphonic tube? Order one with that specification. It will have been tested, with many rejected from a batch. On average RØDE fail 20% of all tubes, this ensures that the ones we do use will be low-noise and low-microphonic.
RØDE Valve mics are sold complete with a power supply and connecting power cable. The power supplies can be repaired or replaced under warranty if faulty, but are not available for individual purchase.
For repairs in your country please contact your local distributor using our technical support page.
All available replacement tubes can be purchased by contacting your nearest authorised service agent / distributor, using our WHERE TO BUY tab at the top of this page.
Unfortunatly RØDE can only supply replacment cables in a standard 10m length. However these cables can be modified by any competent audio service technician.
1" Cardioid Condenser Microphone
1" Studio Condenser Microphone
Multi-Pattern Dual 1" Condenser Microphone
Seamlessly Variable Dual 1" Condenser Microphone
Variable Pattern Dual 1" Condenser Valve Microphone
Limited Edition Vintage-Voiced Valve Microphone
Stereo Microphone for Apple iPhone® & iPad®
1" Cardioid Condenser Microphone
Versatile Studio-Quality USB Microphone
Broadcast-grade stereo on-camera microphone
Active Ribbon Microphone
AI-1 Audio Interface, NT1 Condenser mic, SMR and cables